This baby does everything. This replaces our CHANNEL CREATOR. Want to add a remote start to the factory keyless entry? This unit will do it.



Looking for a low voltage trigger? It will take anything that is around 5 volts and send out a 12 volt remote output

Will bypass the video on a CVA21005/1006/1003, ICA CV800

Latch and unlatch output from a pulsed input. Turn on headlights, neon, etc from an momentary output

Double pulse generator, use in alarm applications where the unlock wire needs 2 pules to unlock all doors

Closed loop circuit, protect trailers on hitches, foglights etc. triggers alarm when wire is cut

Pulse extender, upon a constant or pulsed trigger, the TR 7 will turn on the outputs. As soon as thhe trigger is dosconnected, turned off or at the end of a pulse, the timer will count up to the number of seconds recorded (PULSE TIMER) at which time the output wil turn off. Good for turning on headlights at night

HORN honk output module. On older aftermarket alarms, it may be difficult to disarm the alarm with RF remote when horn is honking. This will give you a 2 second delay betwen honks giving you time to disarm the alarm. Unique horn honking to distinguise your car from others. Perfect to add horn honking to any alarm.

Linear actuator controller, open and close amplifier racks from a momentary source like from an alarm negative output. Sequence is START, STOP, REVERSE, STOP

Doorlock pulse generator : Add ignition control doorlocks

Channel splitter! Split 1 channel from an alarm to 2 outputs! ADD EXTRA OUTPUTS!! Both outputs are programmable for pulsed, latched or timed output

Pulses to constant output. COUNTS a number of user programmable pulses within a programmed time. Good for triggering tracking decies.

3 timers in 1. Upon a constant trigger, all 3 outputs are user programmable to delay before turnon outputs or turning on instantly then delay before turning off outputs. Good for situations where you need more than 1 timer but on a different timer period without having multiple modules

Pulses to LATCH/UNLATCH- Momentary to latch and unlatch a circuit

Pulses to pulse output. Upon a number of pulses within a user programmed time, the OUTPUT will pulse (USE this with any remote start in our alarm department, use it with your FACTORY alarm or keyless entry, hit lock twice and it will REMOTE START your car or other). Programmable to see X amount of pulse before activation (IE: 3 pushes of the LOCK button on your factory transmitter before output is sent)

Pulses to timed output. PULSE TIMER

Latching outputs. 1st pulse will latch one wire. 2nd will unlatch first wire and latch 2nd wire, 3rd pulse will latch both wires. 4th turns off both wires. PERFECT for applications like foglights or other lights which have LOW and HIGH BEAM or for 2 stage accessories!



THIS THING DOES EVERYTHING! GET IT!



• Low voltage trigger

• CVA-1005 Video Bypass

• Latching outputs

• Double Pulse Output

• Pulse Extender

• Horn Honking Output

• Linear Actuator Controller

• Doorlock Pulse Generator

• Channel Splitter

• Pulses to Constant output

• 3 in 1 timer outputs

• Pulses to latch/unlatch outputs

• Pulses to pulse output

• Pulses to timed output

• Latching outputs #2.




UPDATES FROM MANUFACTURER:
DIESEL vehicles.
Problem: The TR-7 will work for a short time and then stops working.
Solution: We recommend using a power noise filter in-line of the power wire of the TR-7 to suppress any electrical spikes caused by the ignition system.


TR-7 and Alpine IVA-D900 fix. You do not need this fix if the instructions that come with the TR-7 has a rev. 1.2.4 in the bottom left corner of instructions.


#1: Low voltage trigger. Supplies a 12 volt remote output for an aftermarket
amplifier when used with a stock head unit that does not have a remote
output. Use the TR-7 to supply a 12 volt output from a 5 volt remote
source, like from Ford radios. Use on some vehicles that have a
negative antenna output and convert to a positive output.
#2: Alpine video bypass. This will automatically bypass Alpine’s flip out monitor
video procedure. WARNING! It is dangerous (and illegal in most
states) for the driver to watch the TV/Video monitor while driving
the vehicle. The driver may be distracted from looking ahead and
an accident could occur. Install the TR-7 only in RV and Marine
applications where there is no parking/hand brake to interface to.
Do not install the TR-7 where the driver may be able to view the
monitor when driving.
#3: Latch and unlatch output from a pulsed input. Turn on headlights, neon
lights or radio from an alarm with a momentary output or from a
momentary switch.
#4: Double pulse output. Pulses outputs twice when trigger from a constant or
pulsed signal. Use for alarm applications where the unlock wire needs 2
pulses to unlock all doors.
#5: Closed loop circuit. Good for monitoring trailers on hitches by triggering an
aftermarket alarm if the trailer is disconnected from the vehicles hitch.
Also monitors stereo equipment in vehicles.
#6: Pulse extender/Delayed turnoff. Upon a constant or pulsed trigger, the
TR-7 will turn on the outputs. As soon as the trigger is disconnected,
turned off or at the end of a pulse, the timer will count up to the number
of seconds recorded, at which time the outputs will turn off. Good for
turning on headlights at night for convenience. Extend alarms output
from 1 second to 3 seconds for Mercedes vacuum door locks. (rev.2)
#7: Horn honking output. On older, aftermarket alarms, it may have been
difficult to disarm the alarm with the RF remote when the horn was
honking. This will give you a 2 second delay between honks, allowing
you to disarm the alarm. Unique horn honking to distinguish your
vehicle from others. Program between 1 and 5 honks before the 2
second delay.
Black (-) Chassis Ground
Green (+) 0.8-16 Volts Input Trigger
Red (+) 12 volts constant/switched
Brown (-) Input Trigger
Blue (+) 12 volt output-2 amps max
White (-) Output-150 ma. max
Orange (-) Output-150 ma. max
MODEL TR-7
Universal Trigger Output Module
OFF-ON
Programming switch must be turned off
after the TR-7 is programmed!
#8: Linear Actuator Controller. Open/close amplifier racks from a momentary
source like from a alarm’s negative output. Sequence is : Start, Stop,
Reverse, Stop.
#9: Door lock Pulse generator. Good for automatically locking and unlocking
door locks when ignition is turned on and off.
#10: Channel Splitter. Split 1 channel from an alarm to 2 outputs. Both outputs
are user programmable for pulse, latched or timed output.
#11: Pulses to constant output. Counts a number of user programmable
pulses within a user programmed time to turn on the outputs. Good for
triggering Vehicle tracking devices that need a constant trigger but the
factory alarm only has a pulsed output when triggered like flashing lights
or horn honking. Keeps factory alarm from triggering Vehicle tracking
device when arming or disarming.
#12: 3 timers in 1. Upon a constant trigger, all 3 outputs are user programmable
to delay before turning on outputs or turning on instantly then delay
before turning off outputs. Good for situations where you need more
than 1 timer but on a different timer period, without having multiple
modules.
#13: Pulses to latch/unlatch outputs. Upon a number of pulses within a user
programmable time, the outputs will latch. Upon a number of pulses
within a user programmable time the second time, the outputs will
unlatch. You may program how many pulses to latch and unlatch. Use to
turn on aftermarket driving lights by using existing parking light switch.
#14: Pulses to pulse output. Upon number of pulses within a user programmable
time, the outputs will pulse. Example, if you programmed to see 4
pulses, for every 4 pulses the TR-7 sees within a 5 second time period,
the outputs will pulse once.
#15: Pulses to timed output. Upon a number of pulses within 5 seconds, the
outputs will turn on and delay for the amount of programmed time, then
the outputs will turn off.
#16: Latching outputs #2. Good for turning on 2 sets of driving lights with one
momentary switch. 1st pulse will latch one wire. 2nd pulse will unlatch
first wire and latch second wire. 3rd pulse will latch both wires. 4th pulse
turns off both wires.


The TR7 has 7 additional Bonus Features not documented in the instructions. These Features are 17-23 as
listed below. Only the TR7 supports these features. The older TR-7 in the black case does not support these
features.

Constant - delayed pulsed output 1 17 On constant trigger - pulse output after programmable time * *
Pulsed input - delayed pulsed output 18 On pulsed input - delay pulse output after programmable time * *
Constant on/off - delayed pulsed output 2 19 On constant trigger - prog. delayed pulsed output, when trigger off - prog. delayed pused output. * * * *
Like version# 4, but programmable pulses 20 Programmable pulsed output *
Low Voltage trigger with delayed output 21 Same as Feature #1 with programmable delay. Output stays on for 1 second on trigger off * *
Alternating Pulsed outputs 22 On pulsed input - white and orange wires alternate pulse * *
Constant - Delayed on/off and pulsed output 23 delayed on = 1, delayed off = 2
Count number of pulses to pulse

REMEMBER! PAC does not provide technical support for these Bonus Features. Technical support has no
other information other than the chart above.